Auto Meter 2277 Metric Adapter/Electric Temperature

#ad
Auto Meter 2277 #ad - Popular phantom, sport Comp, And Ultra lite race proven instruments devoted to the metric measurement system. Works on many foreign/domestic engines.

#ad



Auto Meter 2259 Electric Cylinder Head Temperature Sender

#ad
Auto Meter 2259 #ad - It is sold individually. This sender only works with 1995 and later gauges. 1/8 inch npt replacement for short sweep electric cylinder head temperature gauges and for gauges using sender 2258 in shallow depth areas. 1/8in. Only works with 1995 and later gauges. Can also be used for short sweep electric water, oil and trans temperature gauges where sending unit clearance is an issue.

This sending unit can also be used for short sweep electric water, oil, and trans temperature gauges where sending unit clearance is an issue. Sending unit thread size is 1/8''-27 NPT. Npt replacement for Short Sweep Electric Cylinder Head Temperature gauges.

#ad



Auto Meter 2268 Oil/Temperature Metric Adapter

#ad
Auto Meter 2268 #ad - Can also be used for short sweep electric water, oil and trans temperature gauges where sending unit clearance is an issue. Works on many foreign and domestic engines. Npt female to M14x1. 5 male. 1/8 inch npt replacement for short sweep electric cylinder head temperature gauges and for gauges using sender 2258 in shallow depth areas.

Only works with 1995 and later gauges. Sending unit thread size is 1/8''-27 NPT. 1/8in. It is sold individually.

#ad



ICT Billet LS Engine Swap M16 1.5 Adapter to 1/8 NPT Oil Pressure Sensor LS1 LM7 LR4 LQ4 LS6 L59 LQ9 LM4 L33 LS2 LH6 L92 L76 LY2 LY5 LY6 LC9 LFA LH8 LMG LS3 L98 L9H L20 L94 LZ1 L99 L96 LC8 L77 551172

#ad
ICT Billet 5864172859 #ad - Male m16-1. 5 to female 1/8"-27 npt adapter this adapter installs most commonly in the top-rear, or front-driver side of the engine block to access pressurized oil of the engine. Seals to the block with a sealing washer. This adapter installs most commonly in the top-rear, or front-driver side of the engine block to access pressurized oil of the engine.

Seals to the block with a sealing washer. 1/8" npt taper pipe thread port in the rear of the fitting allows for common sensors or plumbing fittings. Made in wichita, usa produced, Kansas from aerospace grade, billet aluminum. Compatible with: all GM LS Series Engines. Can also be used for short sweep electric water, oil and trans temperature gauges where sending unit clearance is an issue.

ICT Billet LS Engine Swap M16 1.5 Adapter to 1/8 NPT Oil Pressure Sensor LS1 LM7 LR4 LQ4 LS6 L59 LQ9 LM4 L33 LS2 LH6 L92 L76 LY2 LY5 LY6 LC9 LFA LH8 LMG LS3 L98 L9H L20 L94 LZ1 L99 L96 LC8 L77 551172 #ad - Works on many foreign and domestic engines. Only works with 1995 and later gauges. Sold individually with 1 sealing washer. 1/8" npt taper pipe thread port in the rear of the fitting allows for common sensors or plumbing fittings. It is sold individually. Compatible with: all gm ls series engines oil pressure sensor adapter includes: 1 aluminum adapter, 1 sealing washer Made in Wichita, USA produced, Kansas from aerospace grade,  billet aluminum  1/8 inch npt replacement for short sweep electric cylinder head temperature gauges and for gauges using sender 2258 in shallow depth areas.

Sending unit thread size is 1/8''-27 NPT.

#ad



ICT Billet LS Heater Core Bypass Hose Coolant Crossover LS1 LM7 LR4 LQ4 LS6 L59 LQ9 LM4 L33 LS2 LH6 L92 L76 LY2 LY5 LY6 LC9 LFA LH8 LMG LS3 L98 L9H L20 L94 LZ1 L99 L96 LC8 L77 551699

#ad
ICT Billet 551699 #ad - Used to loop the heater hose outlets of your LS/LT engine water pump. Sold individually with 1 sealing washer. Includes 1 black rubber hose. Can also be used for short sweep electric water, oil and trans temperature gauges where sending unit clearance is an issue. Seals to the block with a sealing washer. 1/8" npt taper pipe thread port in the rear of the fitting allows for common sensors or plumbing fittings.

Made in wichita, usa produced, Kansas from aerospace grade, billet aluminum. Compatible with: all GM LS Series Engines. It is sold individually. Heater core bypass hose     this is the tightest bend radius hose on the market custom molded heavy duty hose, better than factory Used to loop the heater hose outlets of your LS/LT engine water pump Used with vehicles that are no longer using the heater core Compatible with all LS or LT series engines from 1998 and newer Includes 1 black rubber hose 1/8 inch npt replacement for short sweep electric cylinder head temperature gauges and for gauges using sender 2258 in shallow depth areas.

ICT Billet LS Heater Core Bypass Hose Coolant Crossover LS1 LM7 LR4 LQ4 LS6 L59 LQ9 LM4 L33 LS2 LH6 L92 L76 LY2 LY5 LY6 LC9 LFA LH8 LMG LS3 L98 L9H L20 L94 LZ1 L99 L96 LC8 L77 551699 #ad - Only works with 1995 and later gauges. This is the tightest bend radius hose on the market custom molded heavy duty hose, better than factory hose. Used with vehicles that are no longer using the heater core. Sending unit thread size is 1/8''-27 NPT. Compatible with all LS or LT series engines from 1998 and newer.

#ad



Spectre Performance 9781 Black 4" 90 Degree Boot

#ad
Spectre Performance SPE-9781 #ad - Includes coupler and two clamps. This adapter installs most commonly in the top-rear, or front-driver side of the engine block to access pressurized oil of the engine. Only works with 1995 and later gauges. Includes 1 black rubber hose. Used with vehicles that are no longer using the heater core. This spectre intake coupler is a 4 inch to 4 inch 90 degree elbow.

Sold individually with 1 sealing washer. Used to loop the heater hose outlets of your LS/LT engine water pump. Can also be used for short sweep electric water, oil and trans temperature gauges where sending unit clearance is an issue. 90 degree coupler for 4 inch diameter intake tubes. Compatible with all LS or LT series engines from 1998 and newer.

Spectre Performance 9781 Black 4" 90 Degree Boot #ad - Made from PVC. This is the tightest bend radius hose on the market custom molded heavy duty hose, better than factory hose. The coupler is not recommended for turbo-charged/supercharged engines. Seals to the block with a sealing washer. 1/8" npt taper pipe thread port in the rear of the fitting allows for common sensors or plumbing fittings.

Made in wichita, usa produced, Kansas from aerospace grade, billet aluminum.

#ad



Lokar TC-1000LS1 36" Hi-Tech Throttle Cable Kit for GM LS1 Engine

#ad
Lokar TC-1000LS1 #ad - Seals to the block with a sealing washer. 1/8" npt taper pipe thread port in the rear of the fitting allows for common sensors or plumbing fittings. Made in wichita, usa produced, Kansas from aerospace grade, billet aluminum. Compatible with: all GM LS Series Engines. This is the tightest bend radius hose on the market custom molded heavy duty hose, better than factory hose.

They are designed with a specially extruded liner for extended life of the cable - not to be confused with ordinary braided brake hose. Aluminum ferrules/instructions/Stainless Steel Housing/Stainless Steel Aluminum Fittings;. Can also be used for short sweep electric water, oil and trans temperature gauges where sending unit clearance is an issue.

Lokar TC-1000LS1 36" Hi-Tech Throttle Cable Kit for GM LS1 Engine #ad - Lokar. 1/8 inch npt replacement for short sweep electric cylinder head temperature gauges and for gauges using sender 2258 in shallow depth areas. The cables mount nicely with Lokar's array of Brackets and Return Springs which are sold separately. It has a "u-cut-to-fit" outer housing which is available in 24 inch or 36 inch lengths with a "U-Cut-to-Fit" stainless inner wire.

Includes coupler and two clamps. It is sold individually. Used to loop the heater hose outlets of your LS/LT engine water pump.

#ad



Quick Connect Fuel Rail Line Adapter Fitting LS LS1 LS3-6AN to 3/8 Hose GM, AN808-02B

#ad
ICT Billet FBA_AN808-02B #ad - Works on many foreign and domestic engines. Warranty: Yes. Lokar tc-1000ls1 hi-tech throttle cable kit; fits w/ls1/ram jet 350; u-cut-to-Fit; 36 in. Incl. Black anodized Aluminum Finish. Sending unit thread size is 1/8''-27 NPT. Compatible with all LS or LT series engines from 1998 and newer. This adapter installs most commonly in the top-rear, or front-driver side of the engine block to access pressurized oil of the engine.

Authorized dealer - 100% Satisfaction Guaranteed. Used to loop the heater hose outlets of your LS/LT engine water pump. Aluminum ferrules/instructions/Stainless Steel Housing/Stainless Steel Aluminum Fittings;. Sold individually with 1 sealing washer. Made from PVC. Seals to the block with a sealing washer. 1/8" npt taper pipe thread port in the rear of the fitting allows for common sensors or plumbing fittings.

Quick Connect Fuel Rail Line Adapter Fitting LS LS1 LS3-6AN to 3/8 Hose GM, AN808-02B #ad - Made in wichita, Kansas from aerospace grade, usa produced, billet aluminum. Compatible with: all GM LS Series Engines. It is sold individually. Connects 6an hose end to factory 3/8" fuel rail or hard line.

#ad



Russell 640853 -6 AN Male to 3/8" SAE Quick-Disconnect Female Push-On EFI Fitting

#ad
Russell 640853 #ad - For racers and performance enthusiasts who want high quality plumbing that's lighter and easier to assemble than traditional braided steel hose, Russell is the perfect choice. Can also be used for short sweep electric water, oil and trans temperature gauges where sending unit clearance is an issue. 90 degree coupler for 4 inch diameter intake tubes.

Used to loop the heater hose outlets of your LS/LT engine water pump. Authorized dealer - 100% Satisfaction Guaranteed. Tc-1000ls1. It is sold individually. Compatible with all LS or LT series engines from 1998 and newer. Sold individually with 1 sealing washer. Connects 6an hose end to factory 3/8" fuel rail or hard line.

Russell 640853 -6 AN Male to 3/8" SAE Quick-Disconnect Female Push-On EFI Fitting #ad - This is the tightest bend radius hose on the market custom molded heavy duty hose, better than factory hose. 1/8 inch npt replacement for short sweep electric cylinder head temperature gauges and for gauges using sender 2258 in shallow depth areas. This adapter installs most commonly in the top-rear, or front-driver side of the engine block to access pressurized oil of the engine.

Black anodized Aluminum Finish. Great option where space is limited.

#ad



LS Engine to Transmission 4L60e Bell Housing Bolts Set Kit T56 LS1 4L60 LS2 551652

#ad
ICT Billet FBA_551652 #ad - Aluminum ferrules/instructions/Stainless Steel Housing/Stainless Steel Aluminum Fittings;. This adapter installs most commonly in the top-rear, or front-driver side of the engine block to access pressurized oil of the engine. Made in wichita, Kansas from aerospace grade, usa produced, billet aluminum. Includes 1 fitting.

Lokar tc-1000ls1 hi-tech throttle cable kit; fits w/ls1/ram jet 350; u-cut-to-Fit; 36 in. Incl. Great option where space is limited. No washers needed with these flanged headed JIS spec bolts. Used to loop the heater hose outlets of your LS/LT engine water pump. Set of 8 ls engine to transmission bellhousing bolt kit     compatible with all gm automatic and manual transmissions that are bolted to an LS or LT Gen 3, & 5 series engine All ICT Billet metric flange bolts are custom made for us, 4, right here in the USA!! Bolts are clear zinc coated steel,  Grade 10.

LS Engine to Transmission 4L60e Bell Housing Bolts Set Kit T56 LS1 4L60 LS2 551652 #ad - 9, jis head 35mm length includes 8 bolts torque spec for bellhousing bolts is 37 ft-lb 1/8 inch npt replacement for short sweep electric cylinder head temperature gauges and for gauges using sender 2258 in shallow depth areas. Authorized dealer - 100% Satisfaction Guaranteed. Used with vehicles that are no longer using the heater core.

For competition applications where reduced weight is needed, use our lightweight ProClassic Crimp-On hose ends. Made in the USA bolts.

#ad



LS Engine Swap M12 1.5 Adapter to 3/8 NPT Coolant Temperature Sensor Water LS1 LSX LS3, 551179

#ad
ICT Billet 551179 #ad - Connects 6an hose end to factory 3/8" fuel rail or hard line. Aluminum ferrules/instructions/Stainless Steel Housing/Stainless Steel Aluminum Fittings;. Can also be used for short sweep electric water, oil and trans temperature gauges where sending unit clearance is an issue. Male m12-1. 5 to female 3/8"-18 npt adapter     this adapts sbc/bbc 3/8" npt coolant temperature sensors to fit into ls series cylinder heads Compatible with: all GM LS Series Engines Made in Wichita, billet aluminum Includes: 1 aluminum adapter, Kansas from aerospace grade, USA produced, 1 sealing washer Will fit sensors with .

85" length, measured from probe tip to the outer edge of adapter. Tc-1000ls1. No washers needed with these flanged headed JIS spec bolts. Sold individually with 1 sealing washer. Lokar. Refer to thread chart to check your correct fitting size. Zinc coated for long lasting corrosion protection and prevents threads from seizing.

LS Engine Swap M12 1.5 Adapter to 3/8 NPT Coolant Temperature Sensor Water LS1 LSX LS3, 551179 #ad - 90 degree coupler for 4 inch diameter intake tubes. Lokar tc-1000ls1 hi-tech throttle cable kit; fits w/ls1/ram jet 350; u-cut-to-Fit; 36 in. Incl.

#ad